Roar

CodeUDescriptionPrice
RE0317

Inclined cover with tile cover. Thermochip and Texaplac base.

Training of inclined roof with an average slope of 26%, on laminated wood beams (not included in this price), composed of the following elements: chained sandwich panel, composed of: upper face of hydrophift agglomerated board of 10 mm d ' Thickness, polystyrene foam insulator core Extruder of 60 mm thickness and lower face of natural spruce frieze, structural frame; Waterproofing: plate under tile fixed with screws to support; Coverage: Curved ceramic tile, 40x19x16 cm; Looked with screws thread-wood on wooden wooden ribs treated or red pine, 42x27 mm and quality wine. Even p / p caring tile p, lateral finish, ventilation and special pieces for formation of carers, hopwhaters, eaves and free ranges.

145,68 €
RE0592

Non-transitable flat cover, not ventilated, with gravel protection

Formation of non-transitable flat roof, not ventilated, with gravel, inverted type, slope of 1% to 5%, composed of the following elements: layer regularization: layer of mortar regain of waterproofing cement of 2 cm in thickness, cruminated and clean ; Waterproofing: Polibreal, or similar solution, consisting of the formation of a waterproofing membrane applied in a liquid and hot way, based on Modified Betuns with polymers, and which conforms an elastic coating totally adhered to support, according to DITE -07/0131 and It consists of: 1. Polibreal® Mastic Coat, minimum thickness 3 mm and a consumption of 4 kg / m², 2. Placing internal sheet separator of smooth aluminum separator not less than 30 microns or external sheet of reinforcement of reinforcement of Polyester film of 50 microns, 3. Layer of Polibreal® mastic, of minimum thickness 3 mm and a consumption of 4 kg / m², 4. Installation of external sheet reinforcement of polyester film of 50 microns; Separator layer Under insulation: Placement of non-woven geotextile lamina composed of polyester fibers joined by Tiretes, (150 g / m²); Thermal insulation: 2 rigid panels of extruded polystyrene, smooth surface and medium-mid-moving machining, 40 mm thick Each panel (total thickness: 80 mm), compression resistance> = 300 kPa, thermal resistance 1.2 m²K / W, thermal conductivity 0.034 W / (MK); Separator layer Under protection: Placement of non-woven geotextile lamina composed of polyester fibers joined by Tiretes, (200 g / m²); Protection layer: 16 to 32 mm diameter pebble coat, exempt from fine, extended with a thickness medium of 10 cm, and perimeter reinforcement of self-protected asphalt lamina according to norm. Even previous cleaning of support, rethinking, bibor formation, sinks and other special elements with reinforcement bands and placed sheets adhered with previous blower primer, mines and ridges, according to DB HS-1 of the CTE and UNE-104 standards .

49,90 €
RE0400

Undertaken transitable flat cover

Flat, transitable and non-ventilated cover of private use, conventional with fixed pavement with sheet formation of vapor barrier adhered with blower on primer layer, formed by: regularization layer and improvement of roof levels, thermal insulation formed For extruded polystyrene (XPS) panels of 40 mm thick and k = 0.029 w / mºC, layer separator of fiber fiberglass of 120 gr / m² available floating on the thermal insulation with simple overlap, waterproofing by means of a bicapa membrane Not adhered to support consisting of two sheets of oxiasfalt united together in all its surface, the bottom armed with fiberglass fierro (LO-40-FV) and the superior with polyester felt (LO-40-FP) Antiadherent separating layer formed by polyethylene film of 0.50 mm thick floating on waterproofing with simple overlap, cement mortar layer for 5 cm ballast and 30x30 c2 ceramic pavement of 30x30 cm on layer of 2.5 cm d and mortar of waterproofing cement, even previous cleaning of support, rethinking, formation of bibs, dimensions, sinks and other special elements with reinforcement bands, mines and ride. Measure in horizontal projection.

87,80 €
RE0377

Flat cover, transitable

Flat cover, transitable, conventional with fixed pavement with 0.8 mm thick EPDM sheet with welding between pieces and with high performance vapor-formation waterproofing, formed by thermal insulation formed by polystyrene panels Expanded EPS- 1i1 of 30 mm thick and k = 0.032 w / mo, separator layer of 0.50 mm polyethylene film of thickness that is floating on the thermal insulation with simple overlap, waterproofing by monolayer membrane not adhered to support Constituted by an ethylene foil Propilè diè Monomer EPDM of 1.5 mm thick, separating layer Antiadherent - antipunzanant formed by polyester felt of 300 g / m² arranged floating on the waterproofing with simple overlapping and pavement of 20x10cm Catalan rajoleta 2.5 cm layer of mortar waterproofing cement, even previous cleaning of support, rethinking, pitcher formation, difells, sinks and other special ements with reinforcement bands, Singles and riding. Measure in horizontal projection.

73,36 €
RE0069

Demolition Catalan cover of subtraction and desk walls, with pneumatic hammer.

Demolition of deck in Catalan, with subtraction and countertop walls of two tile threads, with pneumatic hammer, withdrawal of rubble and load on truck or container, without including transport to landfill.

15,37 €
RE0375

Base training leveled in fiberrocement cover

Flat surface formation on existing inclined roof of wavy plates of fiberrocement, consisting of recurs with medium thickness of medium thickness 6 cm lightening with armed arch, to create a flat base inclined, and waterproofing with an asphaltic lamina LBM-40 FP protected auto mineral Even formation of perimeter parapists, dumping of lightened arlita and armed with mesh 31x31 mm steel 1,5 mm galvanized, auxiliary means, necessary scaffolds, withdrawal of excess material and total cleaning. Checked their tightness.

45,95 €
RE0058

Waterproofing covered with paint in polyurethane, armed.

Non-destructive waterproofing of transitable flat roofs, terraces or balconies made above the fixed pavement, through the application of two layers of elastic coating waterproofing based on liquid monocomponent polyurethane armed liquid with fabric of fiberglass and a layer of paint finish Elastoplastic protection resistant to ultraviolet rays, even cleaning and sanitation of the support prior to the placement of waterproofing.

20,53 €
RE0221

Waterproofing Transitable flat cover and paved tile.

Flat, transitable, conventional with fixed pavement and polyethylene film of 0.2 mm thickly over overlapping for low-performance vapor barrier formation, formed by layer of thick cell concrete between 2 and 30 cm finished With a layer of regularization of 1.5 cm of cement mortar (1: 6) swirling, thermal insulation formed by polystyrene panels extruded XPS-IV of 30 mm thick and k = 0.028 W / MºC, separator layer for felt Fiberglass of 120 gr / m² available floating on thermal insulation with simple overlap, waterproofing by membrane BICAPA PN-7 improved (UNE 104402/96) does not adhered to support formed by two modified bitumen sheets together with each other in all Its surface, the bottom armed with fiberglass (LBM-40-FV) and the superior with polyester felt (LBM-40-FP), an antiadherent separating layer formed by polyethylene film of 0.50 mm thick Willing floating Sob re Waterproofing with simp Solidation and pavement of 20x10cm Catalan Rajoleta on 2.5 cm from waterproofing cement mortar, even prior cleaning of support, rethinking, formation of perimeter edges, bibs, minves, sinks and other special elements with reinforcement bands , mining and riding. Measure in horizontal projection. The formation of slopes with lightweight concrete mixed with expanded clay (lightweight archive for covers) is valued

73,84 €
RE0059u

Waterproofing of embroidering drainage in Terrassa

Repair of waterproofing vertical drainage in flat roof, consisting of: primer layer with 0.35 kg / m² of black bituminous emulsion type EB, two pieces of reinforcement of LBM-30-FP type sheet of 60 cm of 60 cm Wide lower and 80 cm the upper, 30 gr / dm² and polyester felt armor, adhering to support, casseroleum and each other. The casserole will be placed between the two bands of reinforcement and the membrane of the waterproofing of the cover above the two (not included).

18,85 €
RE0084m

Waterproofing of the coronation of the ASSPIT wall, width 15 cm.

Waterproofing of the coronation of the covered sill, constituted by: Asphalt primer with anionic bituminous emulsion EA type and bitumen sheet modified with elastomer SBS, type LBM (SBS) -30-FP, totally adhered to support with blower. For the waterproofing of the coronation of the wall, the raiset of the horse will be held and then placing the waterproofing will restore this (not included).

8,88 €
RE0023

Chopped from tile binding material

Demolition of cement mortar as tile union material on the roof, with manual means, even withdrawal of demolition and load on truck or container, without including transport to landfill.

4,70 €
RE0593

Protection and thermal insulation of flat cover practicable with filter slab

Protection and thermal insulation of flat cover Practicable, consisting of supply and placement of filter and insulating slab in one piece, of dimensions 50 cm x 50 cm and total thickness of 75 mm, formed by a layer of concrete of 35 mm of Thickness and a thermal insulator of extruded polystyrene, thick 40 mm, density 35 kg / m³ and thermal conductivity XPS 0.034 W.

10,66 €
RE0376

Cover skirt repair

Cover skirt repair less than 20 meters away, in Canal and welcomes, with ceramic tile curved Arab type (1.70 kg / ut), artificially aged, 50x23x15 CRN, at the rate of 24-25 UT / m² and receiving with cement mortar 11-35m-2.5A (1: 8), one in 5 letters perpendicular to the eaves, or with ceramic flat tile for central zone, even rethinking, placement of tiles with corner settled on coca de mortar Starting with the eaves hnea, even cleaning and watered from the surface, according to NTE / QTT-11. Previously an undulin type plate under tile below the whole tile and on existing support.

79,52 €
RE0114

Sanitated from floor-silling coating. SUP 30%.

Sanitation of the coating of the terrace's springs, consisting of the punctual chopping of areas in poor condition and reconstruction with cement mortar Dosage 1: 6, even withdrawal of excess material and cleaning.

15,81 €
RE0117

Non-transitable rooftop protected auto

Non-transitable roof protected auto made without vapor barrier, layer of increase in roof levels for improvement, regularization layer with 2 cm thick waterproofing mortar, primer with bituminous black emulsion type ed and performance not less than 0.3 kg / m² , waterproofing with a monolayer solution adhered to blower, with modified LBM-50 / G-FP type lamina of 50 gr / dm² of total mass, protected auto with colored mineral granules and armed with polyester felt, even prior cleaning of the Support, rethinking, bibor formation, sinks and other special elements with lBM-40-FP sheet bands, placed adherents with previous blower printing, mining and riding, according to DB HS-1 of the CTE and norms UNE-104.Incluso Profile L for fixing of an aphile sheet.

38,48 €