Pasta

CodeUDescriptionPrice
RE0077m

Coating raised plaster / mortar in interior cracks, strip of width 20 cm.

Raised and removal, with manual or mechanical means, wide strip 10 cm on each side of the crack. Open the lip of the same so that it can penetrate a mortar of repair and adherence between the two lips of the fissure. Not considered the repair mortar application.

7,47 €
RE0123u

Palette grants for structural recognition

Palette aids for the execution of checking tasting in structural recognition of existing building, consisting of 6 tastings of 10x10 cm on pillar and / or beams until reaching structural concrete, 1 based on 0.60x0 foundation , 60x1.10 m deep to find the shoe, and 4 tastings of 0.40x0.40 approximately in false ceiling of housing to access the lower forged face, even replacement of the CATES to its initial state, Cover of regattas, replacement of coatings, well-covered with compacted land filling, solera and similar paved, and vacuum cover in false ceiling with plasterboard and painted from its surface, even necessary buildings and auxiliary means, Runes withdrawal, excess material and final cleaning.

810,49 €
RE0144

Pottering forged concrete beam.

Shoring of forged self-resistant beams of lights up to 4.5m, with compounds, sleeping and metallic struts, considering 5 uses on wooden elements and 50 uses in metallic struts, even disappointment, cleaning and storage.

5,33 €
RE0050

Breaked cement mortar base, master.

Training on facades and interior walls, of base layer of 15 mm thick, for continuous double layer coatings, with plastering of cement mortar, gray, cement composite, selected aggregates and additives, end-up, waterproof finish 'rain water. Manually applied on a ceramic brick surface, brick or concrete block or thermoargile block. Even proportional part of preparation of the surface support, placement of fiberglass mesh antalcalis for reinforcement of meetings between different materials and in the forged fronts, 20% of the surface of the parament, training of boards , corners, masters, edges, grinding, branches, lintels, finishes in meetings with walls, coatings or other elements received on their surface.

18,79 €
RE0049

Base buzzer, with cement mortar in good view.

Formation on facades and interior walls, of 15 mm thick layer, for continuous double layer coatings, with plastering in good view of cement mortar, gray, cement composed, selected aggregates and additives, endewly finished, waterproof to rainwater. Manually applied on a ceramic brick surface, brick or concrete block or thermoargile block. Even proportional part of preparation of the surface support, placement of fiberglass mesh antalcalis for reinforcement of meetings between different materials and in the forged fronts, 20% of the surface of the parament, training of boards , corners, masters, edges, grinding, branches, lintels, finishes in meetings with walls, coatings or other elements received on their surface.

13,41 €
RE0210

Breakdown, with cement mortar.

Coating of interior and exterior paraments with plastering of industrial mortar for plastering, 15 mm thick, gray, smooth finish, for the realization of the base layer with continuous double layer coatings, finished lirred, thickness 15 mm, Applied manually, armed and reinforced with anti-mesh in the material changes and in the forged fronts.

26,70 €
RE0057

Swallowed swirling good view, with cement mortar.

Breaded with mortar of dosing cement M-15, in vertical walls as a tiled base, according to NTE / RPE-7, measured at ribbon run.

13,57 €
RE0019u

Inspection cove in pillar or reinforced concrete beam.

Inspection cove on pillar or reinforced concrete beam to check the state of the armor, consisting of a maximum of three coves, to be determined by technician, visual inspection and determination of geometry, aspect of concrete, thickness of the coating, depth of carbonation, resistance to the chopped, interaction, number of bars and diameter of the armor and degree of oxidation and loss of section of the armor, in accordance with the 'Guide for Inspection and Complementary Evaluation of concrete structures in existing buildings' of the Valencian Institute of Building IVE (DRB 05/09). Includes: displacement of personnel and equipment, auxiliary means, protection of furniture, preparation and work grants, removal of ruins and cargo up to container or truck, graphic and photographic documentation of the cove, replacement with structural mortar and issuance of ACTA. It does not include: auxiliary means for heights exceeding 7 m, replacement of coatings, manual means, replacement of concrete or transport to landfill.

176,03 €
RE0037

Placement of natural stone threshold and ramp formation Access to lobby.

Supply and placement of granite tile pavement (model to be specified), for exteriors, on a threshold access to community lobby, in 80x120x2 cm wide pieces, polished finish; Received with cement mortar, with M-5 spring sand, made in work without retardants. Even formation of continuous perimeter together, in width not less than 5 mm, in the limits with walls, exempt pillars and level elevations and, where appropriate, partition boards and structural or expansion joints existing in the support; Fixed with mortar of cement boards, CG1, for minimum board (between 1.5 and 3 mm), with the same tonality of the pieces and cleaning. Placed in slope to set up ramp to 25% slope.

80,64 €
RE0482

Demolition Coating of compression with breastfeeding in traditional ceiling

Concrete compression layer demolition, with emptying in the breast area, considering an average thickness of 8 cm thick, in slabs, with manual media and pneumatic hammer, prior raised from the pavement and its base (not included in this price ). Also cleaning, stacking, removal and car loading of rubble on truck or container.

17,86 €
RE0076

Demolition of forged concrete beams

Demolition of forging of concrete beams, with pneumatic hammer and compressor, removal of ruins and load on truck or container.

59,43 €
RE0125

Demolition of forged reinforced concrete, with metallic beams.

Demolition of unidirectional forged concrete reinforced with metallic beams formed type IPE-IPN, intervening of ceramic or concrete bills and concrete compression layer, with manual media, compressor pneumatic hammer and equipment of oxygen, even raised pavement, Proportional part of cleaning, gathering, withdrawal and manual load of rubble on truck or container.

66,65 €
RE0070

Demolition Solera de Concrete en Massa, thickness 10 cm.

Demolition of continuous pavement of concrete in mass of 10 cm thick, with pneumatic hammer, without including the demolition of the base support or deteriorate the constructive elements contiguous. Even proportional part of cleaning, gathering, removal and cargo manual of rubble on truck or container, without including transport to the landfill, according to NTE / ADD-13.

9,42 €
RE0046

Demolition Solera Concrete, thickness 10/12 cm.

Demolition of continuous mass concrete pavement of 10 cm thick, with compressor pneumatic hammer, without including the demolition of the base support or deteriorate the contiguous constructive elements. Even proportional part of cleaning, gathering, removal and manual cargo of rubble on truck or container.

17,26 €
RE0055

Tiled with porcelain tile, placed with adhesive C1.

Supply and placement of tiled with polished porcelain stoneware, 1/0 / - - (Parament, type 1; without additional requirements, type 0; no additional requirement, type - / -), 40x40 cm, € 22 / m² , received with normal cement adhesive, C1 without any additional feature, gray, with double gluing. Even proportional part of preparation of the surface plaster support or plasterboard; Replacement, cuts, PVC cantoners, and together; Rejuncher with white cement, L, BL-V 22.5, for minimum board (between 1.5 and 3 mm), colored with the same tonality of the pieces; Finished and final cleaning. Not included the base support base with cement mortar ruler.

42,28 €
RE0086

Tiled Catalan Baldosí, in forged cantilever.

Supply and execution of facade pavement, by means of thick layer method, with Catalan tile of 12x24 cm, received with mortar of cement m-5 of 3 cm thick, moistened and sprinkled with the surface, rejunctured with cement bean At the minimum board, even part of the reconsiderations, cuts, training of together and socket, elimination of excess material and final cleaning.

24,87 €
RE0052

Tiled porcelain tiles placed with glue cement adhesive.

Supply and execution of pavement through the method of placing in thick layer, ceramic tile of porcelain stoneware, polished 2/0 / - (pavements for traffic for mild pedestrians, type 2; No additional requirements, type 0 ; No additional requirement, type - / -), from 41x41 cm, € 22 / m²; Received with normal cement adhesive, C1 without any additional characteristic, gray, with double gluing, and rejoed with white cement beey, L, BL-V 22.5, for minimum board (between 1.5 and 3 mm) , colored with the same tonality of the pieces. Even proportional part of cleaning, surface checking support, rethinking, cuts, continuous perimeter formation, in width not less than 5 mm, in the limits with walls, exempt pillars and level elevations and, if applicable, if applicable, if applicable, Partition joints and structural boards existing in the support, elimination of the excess material from the rejuncture and final cleaning of the pavement.

44,59 €
RE0119m

Capri Calcary Stone Capri Spitting Capri.

Formation of Capri calcareous spitter, from 110 to 150 cm in length, from 21 to 25 cm wide and 2 cm thick, with trornaaaas, face and edge polished, with clear slope and embedded in the jambs, covering the Settings, departments of the parameters, facade cornices, etc., received with mortar of hydrophift cement M-10. Even proportional part of preparation and regularization of support with mortar of hydrophift cement M-10, riddled between pieces and unions with walls with mortar of special boards for natural stone coatings.

25,89 €
RE0078m

Fissure filling with Mortar Sika Monotop 612.

Fill the crack with Sika Monotop 612, properly tightening, because one and pasting the two lips of the crack, raising up to the ceramic wall plan.

10,59 €
RE0219

Unidirectional forged inclined reinforced concrete, edge 25 + 5 cm, Biga T18 authoresistant.

Unidirectional reinforced reinforcement, inclined, made on two levels, with free plant height between 3 and 4 m, edge 30 = 25 + 5 cm, made with concrete HA-25 / B / 20 / IIA manufactured in work, and poured with Cubilot with a total volume of concrete according to calculation, and Acer UNE-EN10080 B 500 s in the reinforcement zone of negatives and connectors of beams and rings, with a total amount according to plans of structure and detail; Continuous formwork with struts, metallic sprouts and formofrant surface of reinforced wooden wood with bars and profiles; Pretensadat-18 Boigue; Revoltó de Concrete, 60x20x25 cm, even proportional part of special pieces; Compression layer of 5 cm thick, with cast armor formed by electrosoldada mesh ME 25x25Ø 5-5 B 500 T 6x2.20 UNE-EN 10080. Even proportional part of rim hoops. Included cleaning and removal of ruins.

111,07 €
RE0348

Training pending concrete lightened thickness 11 cm

Formation of flat roof slope with 11 cm of medium thickness of cellular lightweight concrete, with cement and lightening products, finished with 1.50 cm cement mortar layer for regularization of slopes, even demolition of The formation of impaired slope, rethinking, proportional part of environments-guides and limes, ruled of the same minves, breaks, swirling of mortar and cleaning, according to NTE / QA, withdrawal and loading of rubble on truck or container without transportation in the landfill

21,55 €
RE0082

Hydrophobic impregnation on absorbent surfaces.

Hydrofuge impregnation, for concrete surfaces, applied in 2 layers by means of roller, even previous cleaning of the support.

13,75 €
RE0138m

Fissure injection in concrete, with epoxy resin.

Injection of cracks in concrete surfaces with epoxy resin of low viscosity, even surface cleaning of the crack

7,32 €
RE0213

Crushed cement mortar raised, in interior walls.

Cracked cement cracked, applied on internal vertical parament of up to 3 m in height, with electric hammer, eliminating it totally without deteriorating the surface support that will be uncovered and prepared for its subsequent coating. Even proportional part of manual cleaning with brush of hard bristles, gathering, removal and manual load of rubble on truck or container.

8,86 €
RE0211

Chopped coating Monolayer mortar.

Chopped monolayer mortar applied on internal vertical parament of up to 3 m in height, with electric hammer, eliminating it totally without deteriorating the surface support that will be revealed and prepared for its subsequent coating. Even proportional part of cleaning, gathering, removal and manual cargo of rubble on truck or container.

9,83 €
RE0023

Chopped from tile binding material

Demolition of cement mortar as tile union material on the roof, with manual means, even withdrawal of demolition and load on truck or container, without including transport to landfill.

4,70 €
RE0060

Chopped outside wall / Interior cement mortar, thickness less than or equal to 3 cm

Chopped outside / interior wall with cement mortar coatings, with a medium thickness or equal to 3 cm, and chopped joints completely eliminating plaster and concretions up to 2 cm deep, for the subsequent application on the support of The stucco or plaster, executed by mechanical procedure through a small pneumatic hammer operated with a portable compressor; Even withdrawal and loading of rubble on container or truck for landfill transport, measure the surface executed on ribbon run without vacuum deduction.

6,99 €
RE0215u

Reinforcement collar on the basis of 16x25 cm concrete pillar, with PNL40.4

Base of reinforcement of pillar of reinforced concrete 25x25 or diameter 25 cm through necklers of metallic angles PNL-40.4 mm of steel S275 hot laminate, joined by welding, even welding in situ and filling of Space between concrete and steel with a layer of 1.5 mm epoxy resin in two components.

124,55 €
RE0216m

Metallic reinforcement of 16x25 cm concrete pillar, with PNL40.4

Reinforcement of rectangular reinforcement reinforcement of dimensions 25x25 cm for confinamiemto of trellis of 4 standardized water laminated steel S275 PNL-40.4 mm of 2.42 kg / m according to UNE 10025-2 arranged in the edges of the support and joins The four faces through metal welded metallic planks on site, every 25 cm, by constriction by cooling, even contribution of welding material according to UNE-EN ISO 2560, worked and placed.

310,31 €
RE0116m

Repair or replacement Ceramic sockets.

Repair or replacement of ceramic piece Type socket in poor condition, on the perimeter of terrace, chopped piece and mortar of union, disposition of a similar piece taken with mortar of cement 1: 6, parts and final cleaning.

8,31 €
RE0064m

Successful repair forged singing and coating, width 35 cm.

SANITE AND REPARATION Wrought chanting seen wide 35 cm, in the main access and housing access, prior chopped coating or in poor condition, structural sanitation of structural concrete, passivate of armor and reconstruction of the section affected with mortar of resins type applicatecr4 or similar, reconstruction of edges and surface finish with plastering cement mortar 1: 6 in good view, final coating application with painting in silicate in tones similar to the existing one, even auxiliary means, necessary scaffolding , withdrawal of excess material and cleaning.

39,53 €
RE0114

Sanitated from floor-silling coating. SUP 30%.

Sanitation of the coating of the terrace's springs, consisting of the punctual chopping of areas in poor condition and reconstruction with cement mortar Dosage 1: 6, even withdrawal of excess material and cleaning.

15,81 €
RE0227

Sanitated stone walls seen in interiors

Sanitation of stone walls, in interior housing cloth, consisting in: Emptying stone joints in a depth of 2 to 5 cm, replacing gradient stones and bricks and clean with a metallic brush. Fill the joints, gaps and huts of support with the base mortar of plastering, or directly with the coatings. Also stacking, removal and burden of rubble and remains generated on truck or container

30,18 €
RE0121

Thermocal thermocal system of thermal insulation and mineral facades coating.

Facade energy rehabilitation, through thermal insulation and mineral facade coating, on its outer face, with the Thermocal Dbblok system, consisting of a layer of mortar of thermal and acoustic insulating, thermocal, 20 mm thick, applied through Mechanical projection with a 15 kg / m² performance, and a layer of lime monolayer mortar, Ibercal Master 450 Thermo, endeared finish, color to choose, 10 mm thick.

32,07 €
RE0224

Solera de Concrete en mass T1, thickness 10 cm, finished bearing.

Training continuous concrete pavement in mass of 10 cm thick, made with concrete HM-20 / F / 12 / and manufactured in central and poured with pump; Treaty superficially with tread mortar, light gray color, composed of cement, selected aggregates of quartz, organic pigments and additives, with an approximate performance of 3 kg / m², manually sprinkled over the still fresh concrete and subsequent application of colorless curing liquid , performance 0.15 kg / m². Even P / P cleaning surface support, extended and vibrated from the concrete through vibrant rule, embroplement or connection of the external elements (hoops of boxes, boneres, siphonic boxes, etc.) of facilities networks Executed under the pavement, mechanical swirling of the entire surface until the mortar is totally integrated into concrete, and final cleaning of the finished surface. Including the preparation of the existing base layer, work joints and concrete, retraction through mechanical media cut with diamond disk at least 2/3 of the thickness of the solera, expansion joints and perimeter together.

33,39 €
RE0217u

Tasting of inspection in lower face Big forged. Aluminosis.

Tasting 1 m² ceiling and sample extraction of pre-strained or armed beam concrete, thus eliminating the plaster of plaster in the lower face of the beam in a length of at least 40 cm, extraction from the sample of no less of 200 gr deepening to be able to see the armor and check its state, through manual methods, without including the necessary repair.

16,66 €
RE0117

Non-transitable rooftop protected auto

Non-transitable roof protected auto made without vapor barrier, layer of increase in roof levels for improvement, regularization layer with 2 cm thick waterproofing mortar, primer with bituminous black emulsion type ed and performance not less than 0.3 kg / m² , waterproofing with a monolayer solution adhered to blower, with modified LBM-50 / G-FP type lamina of 50 gr / dm² of total mass, protected auto with colored mineral granules and armed with polyester felt, even prior cleaning of the Support, rethinking, bibor formation, sinks and other special elements with lBM-40-FP sheet bands, placed adherents with previous blower printing, mining and riding, according to DB HS-1 of the CTE and norms UNE-104.Incluso Profile L for fixing of an aphile sheet.

38,48 €
RE0126

Transport of inert waste and / or concrete with container.

Transport of concrete inert waste, bricks, tiles and ceramic material, produced in construction and / or demolition works, with a container of 4.2 m³, in specific landfill, installation of treatment of construction waste and external demolition in L 'work or center for recovery or waste disposal.

34,81 €