Reinforced concrete

CodeUDescriptionPrice
RE0144

Pottering forged concrete beam.

Shoring of forged self-resistant beams of lights up to 4.5m, with compounds, sleeping and metallic struts, considering 5 uses on wooden elements and 50 uses in metallic struts, even disappointment, cleaning and storage.

5,33 €
RE0019u

Inspection cove in pillar or reinforced concrete beam.

Inspection cove in pillar or reinforced concrete beam to verify the state of the armor, consisting of a maximum of three coves, to be determined by technician, visual inspection and determination of geometry, aspect of concrete , thickness of the coating, depth of carbonation, resistance to chopping, inter-intereters, number of bars and diameter of the armor and degree of oxidation and loss of section of the armor, in accordance with the 'Guide for to the inspection and complementary evaluation of concrete structures in existing buildings' of the Valencian Institute of Building IVE (DRB 05/09). Includes: displacement of personnel and equipment, auxiliary means, protection of furniture, preparation and work grants, removal of ruins and cargo up to container or truck, graphic and photographic documentation of the cove, replacement with structural mortar and issuance of ACTA. It does not include: auxiliary means for heights greater than 7 m, replacement of coatings, manual means, replacement of concrete or transport to landfill.

176,03 €
RE0076

Demolition of forged concrete beams

Demolition of forging of concrete beams, with pneumatic hammer and compressor, removal of ruins and load on truck or container.

59,43 €
RE0125

Demolition of forged reinforced concrete, with metallic beams.

Demolition of unidirectional forged concrete reinforced with metallic beams formed type IPE-IPN, intervening of ceramic or concrete bills and concrete compression layer, with manual media, compressor pneumatic hammer and equipment of oxygen, even raised pavement, Proportional part of cleaning, gathering, withdrawal and manual load of rubble on truck or container.

66,65 €
RE0219

Unidirectional forged inclined reinforced concrete, edge 25 + 5 cm, Biga T18 authoresistant.

Unidirectional reinforced reinforcement, inclined, made on two levels, with free plant height between 3 and 4 m, edge 30 = 25 + 5 cm, made with concrete HA-25 / B / 20 / IIA manufactured in work, and poured with Cubilot with a total volume of concrete according to calculation, and Acer UNE-EN10080 B 500 s in the reinforcement zone of negatives and connectors of beams and rings, with a total amount according to plans of structure and detail; Continuous formwork with struts, metallic sprouts and formofrant surface of reinforced wooden wood with bars and profiles; Pretensadat-18 Boigue; Revoltó de Concrete, 60x20x25 cm, even proportional part of special pieces; Compression layer of 5 cm thick, with cast armor formed by electrosoldada mesh ME 25x25Ø 5-5 B 500 T 6x2.20 UNE-EN 10080. Even proportional part of rim hoops. Included cleaning and removal of ruins.

111,07 €
RE0142m

Bottle Bottle Face Break forged, for reinforcement Motoroviga system.

Chopped from plaster plaster in horizontal walls of the base of the sneakers of beams that have to be reinforced or sanished until they completely leave and clean the lower face of the same for the correct union between these and the system of Reinforcement used, even the proportional proportional part of demolition of the inservigating rivers of forged forged for the correct execution of the reinforcement actions of beams with mechanical or similar system, cleaning, collection and load of rubble on foot of Load.

8,79 €
RE0141m

Bullfight Beautiful Fack plaster

Crushed plasterboard of the lower face of the beams of a forged, until leaving its surface completely seen and clean, even cleaning, collection and loading of rubble in truck or container.

3,68 €
RE0222u

Wooden prosthesis with fiberglass armor.

Broach repair by eliminating the deteriorated area and placing a prosthesis from the same section as the existing beam and up to 30 cm of wild pine saw (Pinus sylvestris), brushed finish, for structural applications, structural quality MEG according to UNE 56544, resistant class C-18 according to UNE-EN 338 and UNE-EN 1912 and protection against biotic agents that correspond to the NP2 penetration class (3 mm in the side faces of the Albeca) according to UNE-EN 351 -1, adhered to healthy wood through epoxy-acrylate resin, styrene free, and later arming with two wood union using 2 fiberglass rods reinforced with polyester resin, 12 mm in diameter, 0 , 05 m in length each, housed in perforations made in the prosthesis and healthy wood. Even proportional part of sanitation of the wooden piece, cutting 60 ° of healthy wood to receive the prosthesis, provisional fixation of the prosthesis through carpenter cats and keys, execution of perforations in the prosthesis and in the wood Healthy, punched with epoxy resin in perforations after placing the rods, polished imperfections, cleaning, stacking, removal and manual loading of demolitions on truck or container.

102,07 €
RE0483m

Reinforcement in bending bending, carbon fiber sheet, Kimia house

Reinforcing flexion for the lower face, through the Kimitech Plate system, formed by carbon fiber laminate of 50 mm wide 1.4 mm thick, and mechanical resistance to breaking according to the direction of the fiber of 3000 MPa, cabbage · Located with Kimitech EP-TX adhesive, on a preceding surface and pressured with Kimicover fixed

RE0215u

Reinforcement collar on the basis of 16x25 cm concrete pillar, with PNL40.4

Base of reinforcement of pillar of reinforced concrete 25x25 or diameter 25 cm through necklers of metallic angles PNL-40.4 mm of steel S275 hot laminate, joined by welding, even welding in situ and filling of Space between concrete and steel with a layer of 1.5 mm epoxy resin in two components.

124,55 €
RE0008m

Forged reinforcement with IPE-100 up to 3.50 m. Includes previous and pointing work.

Functional replacement of forged, in the areas indicated in plans, consisting of the reinforcement of each beam through IPE-100 S-275-JR profiles, in accordance with the description of the project and the directions of the facultative management, including the following materials and works:

94,35 €
RE0009m

Reinforcement of forged IPE-120 up to 3.5 m. Includes previous and pointing work.

Functional replacement of forged, in areas indicated in plans, consisting of the reinforcement of each beam through profiles IPE-120 S-275-JR, in accordance with the description of the project and the prompts of the faculty management, including the following materials and Works:

99,64 €
RE0010m

Reinforcement of forged IPE-140 up to 4 m. Includes previous and pointing work.

Functional replacement forged, consisting of the reinforcement of each beam through IPE-140 S-275-JR profiles, including the following materials and work:

105,16 €
RE0011m

Reinforcement of forged IPE-160 up to 3.5 m. Includes previous and pointing work.

Functional replacement of forged, in the areas indicated in plans, consisting of the reinforcement of each beam through profiles IPE-160 S-275-JR, in accordance with the project description and the prompts of the faculty management, including the following materials and Works:

112,60 €
RE0485m

Reinforcement of forged MVH. Motoroviga, 4,00-4,50 l

Functional replacement of unidirectional forged beam through telescopic-extensible profile with colis zippers for its maximum light adjustment with lights between 4.00 m and 4.50 m. The profile is made in three sections and built in zinc-shaped and bicromated gold-colored steel sheet, with thickness of 4 mm sheet and 6 mm in central. MVH type, supported on posters with chemical anchorage and threaded rods M12X125 with thread and volaster for screwed mounting. With supply of resin of two components threaded rods and mortar according to mechanoviga specifications. Included assembly in work. Measures the executed length.

RE0486m

Reinforcement of forged MVV, Motoroviga, 4,00-4.50 ml

Functional replacement of unidirectional forged beam through a telescopic-extensible profile with colis zippers for its adjustment at maximum light, with lights between 4.00 m and 4.50 m. The profile is made in three sections and built in zincated and bicromatated gold-colored steel sheet, with thickness of 4 mm sheet at ends and 6 mm in central. MVV type, supported by cartel with chemical anchor and threaded rods M12X125 with thread and volaster for mounting screwed or through special support system on existing UPN profile. With supply of resin of two components threaded rods and mortar according to mechanoviga specifications. Previously, the plaster of the vertical setting will be removed and subsequently according to type of forged the part of the cells of the rebellion be made of ceramics or concrete will be prepared to receive the anchors of the posters and in the case To support Murs, a concrete dice under the Bigeta will be held, which will serve as distribution of loads and anchorage point of the system support poster. Subsequently, the MVH assembly will be proceeded. Subsequent assembly of the MVV profile with its sealing to pour the self-leveling mortar being finally embedded the existing beam. Measure the reinforced beam length.

RE0479m

Forged reinforcement with MVV12 Motoroviga system. length 3.50ml

MW12 3250: active reinforcement of beams in unidirectional slabs through the use of three elements of telescopic profile telescopic stainless steel sheet S235JR Zincat type Omega de la Casa Motos MW12 3250 D.I.T. 331 / r coupled and joined together through the use of high resistance screws achieving the transmission of efforts by filling in spaces with controlled retraction mortars and attracted them with mortars without retraction type Betec Serena 110. I. Exempt of chlorides and metallic aggregates and set the system to media through folding steel plates and chemical or mechanical anchors depending on the type of material and in accordance with specifications of the project and the manufacturer, screws D High resistance class 8'8 and M-12. Including the proportional part of mortars of filling and attacking, stainless steel profile, special support or connection systems, supports and support mechanisms as well as all necessary accessories, anchors to resistant structural elements and stainless steel screws, Ended in work, even chopped with enclosures, coatings, chopped of massifs in beams or structural elements and demolition of the corner for the correct coupling of beams, perforations and commissioning, small material and electrical supply necessary, demolition of The upper rows of partitions that act against beams and the plaster coating in vertical and horizontal walls necessary for its execution if it comes or opening of necessary gaps in parts and facades for the maneuver or necessary actions. Fully executed and according to details and project memory and manufacturer specifications. The supply and placement of special pieces and the opening of scaffolding holes is included.

RE0480m

Forged reinforcement with MVV16 Movement System. length 3.50ml

MW16 3250: Active reinforcement of beams in unidirectional slabs through the use of three elements of telescopic profile telescopic stainless steel sheet S235JR Zincat type omega of the MW16 MECANOVIGA House MW16 3250 D.I.T. 331 / r coupled and joined together through the use of high resistance screws achieving the transmission of efforts by filling in spaces with controlled retraction mortars and attracted them with mortars without retraction type Betec Serena 110. I. Exempt of chlorides and metallic aggregates and set the system to media through folding steel plates and chemical or mechanical anchors depending on the type of material and in accordance with specifications of the project and the manufacturer, screws D High resistance class 8'8 and M-12. Including the proportional part of mortars of filling and attacking, stainless steel profile, special support or connection systems, supports and support mechanisms as well as all necessary accessories, anchors to resistant structural elements and stainless steel screws, Ended in work, even chopped with enclosures, coatings, chopped of massifs in beams or structural elements and demolition of the corner for the correct coupling of beams, perforations and commissioning, small material and electrical supply necessary, demolition of The upper rows of partitions that act against beams and the plaster coating in vertical and horizontal walls necessary for its execution if it comes or opening of necessary gaps in parts and facades for the maneuver or necessary actions. Fully executed and according to details and project memory and manufacturer specifications. The supply and placement of special pieces and the opening of scaffolding holes is included.

RE0477m

Structural reinforcement of beams with armed structural mortar reinforcement

Reinforcement of reinforced concrete 12 cm of soul, through reinforced reinforced 6-8 cm in the lower face and width 12 cm, made with structural repair mortar PCC4 Applicatec fluid or similar, Sika monotop PCC50 or Promompa Betec 600 or similar, discharge in interior metal profile in the form of U, section 120x80x4 mm, as a lost formwork, variable trace and overlapping profiles, stubborn with telescopic metallic profile, on dorment of wood, Each 1 m, prior brushing of the beam and elimination of plaster or mortar coatings, surface and passivate repair of armors with inhibitory mortar of corrrosion type EPOCEM or similar, application of resin bridge binding type will arrive or similar, Provision of nuva armor of reinforcement with 2 rods of 12 mm, overcovered in the anchorage armor support, with drilling and injection of epoxy-acrylate resin type Betec n or similar, disposition of rings of diameter 4 mm in shape d 'U anchored to the support of La Bigueta, arranged every 30 cm, resin and linked to the new Longuital armor, preparation of the lost formwork and dumping structural mortar of recreation through injection pumping machine; Unmasked and lateral attacked with structural mortar. Acer UNE-EN 10080 B 500 S, with a quantity of 3 kg linear meter. Even p / p of chopped and sanitated from the lower face of the beam to recreate; Direct connection of the original longitudinal armor and reinforcement through forks conveniently welded with others; cleaning the surface of concrete; Application of a continuous layer of thixotropic adhesive of two components based on epoxy resin, on the surface of the hardened concrete; Assembly of the formwork; spill of concrete; Disassembly of the formwork and cleaning of the remains generated.

RE0216m

Metallic reinforcement of 16x25 cm concrete pillar, with PNL40.4

Reinforcement of rectangular support of reinforced concrete 25x25 cm for confinamiemto of trellis of 4 standardized profiles of hot rolled steel S275 PNL-40.4 mm of 2.42 kg / m according to UNE 10025-2 arranged in the edges of the support and joins On the four sides by means of metal union plants welded in situ, every 25 cm, by cooling constriction, even contribution of welding material according to UNE-EN ISO 2560, worked and placed.

310,31 €
RE0481

Upper reinforcement of unidirectional forged, layer of compression

Superior reinforcement of unidirectional forging of wooden beams, through a layer of compression of reinforced concrete, 5 cm, medium thickness, with reinforcement of negative with 2 of 12 mm and cast mesh 15x15, 8 mm in diameter, executed In situ, concrete lightened with structural arch, resistance 2.5 MPA and density 500 kg / m³, drilling and resin of rods in beams, linked to mesh of cast, even execution of perimeter lace in wall for anchorage of the Army , races in tabiyiería and pp of rings

RE0218

Sanitation of beams in forged and structural repair.

Intervention in concrete beam consisting of: chopped coating ceiling of wetlands to achieve beams, sanitation of armor with manual planner, treatment of armor affected by oxidation by means of passivant product, reconstruction of the beam through special mortars Sika or the like

34,11 €
RE0143m

Structural sanitary face Bottle concrete beaker.

Sanitation concrete or ceramic beam by demolishing existing coating, court of the enclosures or interior partitions that they act against, cleaning the support until they completely clean the concrete or the base of the shoe, sanitation of the zones flipping for Corrosion, passivate of armors with an inhibitory primer of corrosion Sika Ferogard-903 or similar and recomposition of coating with a structural mortar of high initial resistance and controlled shrinking Sika Top or Structurite of the Thoro house or similar. Even small material and auxiliary means necessary for its execution, coatings similar to those that existed prior to the final action and finishes. Fully executed.

18,28 €
RE0038

Solera reinforced concrete of 12 cm, in lift pit.

Training of continuous pavement of reinforced concrete of 12 cm thick, made with concrete HA-25 / B / 20 / III manufactured in Central, carried out in work, and Electrosoldada ME ME 20x20 Ø 5-5 B 500 T 6x2.20 UNE- In 10080, on approved separators; By elevator fossa bottom, even proportional part of the surface cleaning, extended and vibrated concrete.

53,92 €
RE0217u

Tasting of inspection in lower face Big forged. Aluminosis.

Tasting 1 m² ceiling and sample extraction of prestended or armed beam concrete, thus eliminating the plaster of plaster in the lower face of the beam in a length of at least 40 cm, extraction of the sample of no less of 200 gr deepening to be able to see the armor and check its state, through manual methods, without including the necessary repair.

16,66 €